Commit 1724d4e9 authored by David Bauer's avatar David Bauer Committed by Christian Lamparter
Browse files

ath79: add support for devolo WiFi pro 1200e



Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
       1x Atheros AR8033
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: default avatarDavid Bauer <mail@david-bauer.net>
parent 84719443
......@@ -58,6 +58,9 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0@eth0" "1:lan:1" "3:lan:4" "4:lan:3" "5:lan:2" "2:wan"
;;
devolo,dvl1200e)
ucidef_set_interface_lan "eth0 eth1"
;;
dlink,dir-825-b1)
ucidef_set_interface_wan "eth1"
ucidef_add_switch "switch0" \
......
......@@ -87,6 +87,10 @@ board=$(board_name)
case "$FIRMWARE" in
"ath10k/cal-pci-0000:00:00.0.bin")
case $board in
devolo,dvl1200e)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary art 0) -1)
;;
glinet,gl-x750)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
......
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "qca9558_devolo_dvl1xxx.dtsi"
/ {
compatible = "devolo,dvl1200e", "qca,qca9557";
model = "devolo WiFi pro 1200e";
aliases {
led-boot = &status_blue;
led-failsafe = &status_red;
led-running = &status_blue;
led-upgrade = &status_red;
};
leds {
compatible = "gpio-leds";
status_blue: status_blue {
label = "dvl1200e:blue:status";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
default-state = "on";
};
status_red: status_red {
label = "dvl1200e:red:status";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
};
};
beeper {
compatible = "gpio-beeper";
gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
};
};
&mdio1 {
status = "okay";
};
&eth1 {
status = "okay";
};
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
* The hardware of this board family is most likely shared with other devices
* from other manufacturers.
* Devolo seems to use hardware from Edimax, namely the Edimax WAP1750.
*
* The base board is identical but the single models differ in number of
* buttons, ethernet ports, external console, USB, external / internal
* antennas and number of spatial streams.
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "qca9557.dtsi"
/ {
chosen {
bootargs = "console=ttyS0,115200n8";
};
keys {
compatible = "gpio-keys";
reset {
label = "Reset button";
linux,code = <KEY_RESTART>;
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
watchdog {
compatible = "linux,wdt-gpio";
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
hw_algo = "toggle";
hw_margin_ms = <300>;
always-running;
};
};
&pcie0 {
status = "okay";
};
&uart {
status = "okay";
};
&gpio {
status = "okay";
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x040000>;
read-only;
};
partition@40000 {
label = "u-boot-env";
reg = <0x040000 0x010000>;
read-only;
};
art: partition@50000 {
label = "art";
reg = <0x050000 0x010000>;
read-only;
};
partition@60000 {
label = "art_bak";
reg = <0x060000 0x010000>;
read-only;
};
partition@70000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x070000 0xf90000>;
};
};
};
};
&mdio0 {
status = "okay";
phy4: ethernet-phy@4 {
reg = <4>;
at803x-disable-smarteee;
};
};
&eth0 {
status = "okay";
mtd-mac-address = <&art 0x00>;
phy-handle = <&phy4>;
pll-data = <0xae000000 0x80000101 0x80001313>;
gmac_config: gmac-config {
device = <&gmac>;
rxdv-delay = <3>;
rxd-delay = <3>;
txen-delay = <0>;
txd-delay = <0>;
rgmii-enabled = <1>;
};
};
&mdio1 {
phy1: ethernet-phy@1 {
reg = <1>;
};
};
&eth1 {
mtd-mac-address = <&art 0x00>;
mtd-mac-address-increment = <1>;
phy-handle = <&phy1>;
pll-data = <0x03000101 0x00000101 0x00001313>;
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
mtd-mac-address = <&art 0x00>;
mtd-mac-address-increment = <(-2)>;
};
CONFIG_AT803X_PHY=y
CONFIG_BLK_MQ_PCI=y
CONFIG_GPIO_WATCHDOG=y
CONFIG_GPIO_WATCHDOG_ARCH_INITCALL=y
CONFIG_INTEL_XWAY_PHY=y
CONFIG_IP17XX_PHY=y
CONFIG_LEDS_RESET=y
......@@ -23,3 +25,4 @@ CONFIG_RTL8366RB_PHY=y
CONFIG_RTL8366S_PHY=y
CONFIG_RTL8366_SMI=y
CONFIG_RTL8367_PHY=y
CONFIG_WATCHDOG_CORE=y
......@@ -138,6 +138,14 @@ define Device/buffalo_wzr-hp-g450h
endef
TARGET_DEVICES += buffalo_wzr-hp-g450h
define Device/devolo_dvl1200e
ATH_SOC := qca9558
DEVICE_TITLE := devolo WiFi pro 1200e
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1200e
define Device/dlink_dir-825-b1
ATH_SOC := ar7161
DEVICE_TITLE := D-LINK DIR-825 B1
......
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment