This project is mirrored from git://git.openwrt.org/openwrt/openwrt.git. Pull mirroring updated .
  1. 24 Oct, 2020 9 commits
  2. 22 Oct, 2020 4 commits
  3. 21 Oct, 2020 5 commits
  4. 20 Oct, 2020 3 commits
    • Hans Dedecker's avatar
      glibc: update to latest 2.31 commit · b90a4a8e
      Hans Dedecker authored
      4bc9918c99 AArch64: Use __memcpy_simd on Neoverse N2/V1
      4722d1fb9d [AArch64] Improve integer memcpy
      bea507a3f5 AArch64: Rename IS_ARES to IS_NEOVERSE_N1
      d0a5b76902 AArch64: Improve backwards memmove performance
      24a30c5959 AArch64: Add optimized Q-register memcpy
      88db98fa6e AArch64: Align ENTRY to a cacheline
      Signed-off-by: default avatarHans Dedecker <dedeckeh@gmail.com>
      b90a4a8e
    • John Audia's avatar
      kernel: bump 5.4 to 5.4.72 · dd20ba98
      John Audia authored
      All modifications made by update_kernel.sh
      
      Build system: x86_64
      Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
      Run-tested: ipq806x/R7800
      
      No dmesg regressions, everything functional
      Signed-off-by: default avatarJohn Audia <graysky@archlinux.us>
      dd20ba98
    • Richard Fröhning's avatar
      ramips: add support for TP-Link RE200 v4 · 33b76d66
      Richard Fröhning authored
      TP-Link RE200 v4 is a wireless range extender with Ethernet and 2.4G and 5G
      WiFi with internal antennas.
      It's based on MediaTek MT7628AN+MT7610EN like the v2/v3.
      
      Specifications
      --------------
      
      - MediaTek MT7628AN (580 Mhz)
      - 64 MB of RAM
      - 8 MB of FLASH
      - 2T2R 2.4 GHz and 1T1R 5 GHz
      - 1x 10/100 Mbps Ethernet
      - 8x LED (GPIO-controlled), 2x button
      - UART connection holes on PCB (57600 8n1)
      
      There are 2.4G and 5G LEDs in red and green which are controlled
      separately.
      
      MAC addresses
      -------------
      
      The MAC address assignment matches stock firmware, i.e.:
      
      LAN : *:8E
      2.4G: *:8D
      5G  : *:8C
      
      MAC address assignment has been done according to the RE200 v2.
      
      The label MAC address matches the OpenWrt ethernet address.
      
      Installation
      ------------
      
      Web Interface
      -------------
      
      It is possible to upgrade to OpenWrt via the web interface. Simply flash
      the -factory.bin from OEM. In contrast to a stock firmware, this will not
      overwrite U-Boot.
      
      Recovery
      --------
      
      Unfortunately, this devices does not offer a recovery mode or a tftp
      installation method. If the web interface upgrade fails, you have to open
      your device and attach serial console.
      
      Instructions for serial console and recovery may be checked out in
      commit 6d6f36ae ("ramips: add support for TP-Link RE200 v2") or on
      the device's Wiki page.
      Signed-off-by: default avatarRichard Fröhning <misanthropos@gmx.de>
      [removed empty line, fix commit message formatting]
      Signed-off-by: default avatarDavid Bauer <mail@david-bauer.net>
      33b76d66
  5. 19 Oct, 2020 5 commits
  6. 18 Oct, 2020 2 commits
    • Hauke Mehrtens's avatar
      sunxi: Adapt U-Boot config to board rename · 7f5f7384
      Hauke Mehrtens authored
      The board was renamed without changing the BUILD_DEVICES in the U-Boot
      Makefile, this broken the build.
      
      Fixes: 0830ae3a ("sunxi: Correct manufacturer name to Sinovoip")
      Signed-off-by: default avatarHauke Mehrtens <hauke@hauke-m.de>
      7f5f7384
    • Jayantajit Gogoi's avatar
      sunxi: add support for FriendlyARM NanoPi R1 · e6d9f6fd
      Jayantajit Gogoi authored
      Specification:
      
      - CPU: Allwinner H3, Quad-core Cortex-A7 Up to 1.2GHz
      - DDR3 RAM: 512MB/1GB
      - Network:
          10/100/1000M Ethernet x 1,
          10/100M Ethernet x 1
      - WiFi: 802.11b/g/n, with SMA antenna interface
      - USB Host: Type-A x2
      - MicroSD Slot x 1
      - MicroUSB: for OTG and power input
      - Debug Serial Port: 3Pin 2.54mm pitch pin-header
      - LED:
          nanopi:red:status
          nanopi:green:wan
          nanopi:green:lan
      - KEY:
          reset
      - Power Supply: DC 5V/2A
      
      Installation:
      
      - Write the image to SD Card with dd
      - Boot NanoPi from the SD Card
      Signed-off-by: default avatarJayantajit Gogoi <jayanta.gogoi525@gmail.com>
      e6d9f6fd
  7. 17 Oct, 2020 6 commits
    • 张鹏's avatar
      ath79: add support for Qxwlan E1700AC v2 · 4ff7bdfe
      张鹏 authored
      E1700AC v2 based on Qualcomm/Atheros QCA9563 + QCA9880.
      
      Specification:
      
       - 750/400/250 MHz (CPU/DDR/AHB)
       - 128 MB of RAM (DDR2)
       - 8/16 MB of FLASH (SPI NOR)
       - 3T3R 2.4 GHz
       - 3T3R 5 GHz
       - 2 x 10/1000M Mbps Ethernet (RJ45)
       - 1 x MiniPCI-e
       - 1 x SIM (3G/4G)
       - 1 x USB 2.0 Port
       - 5 x LED , 2 x Button(S8-Reset Buttun), 1 x power input
       - UART (J5) header on PCB (115200 8N1)
      
      Flash instruction:
      
         1.Using tftp mode with UART connection and original LEDE image
            - Configure PC with static IP 192.168.1.10 and tftp server.
            - Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
              to "firmware.bin" and place it in tftp server directory.
            - Connect PC with one of LAN ports, power up the router and press
              key "Enter" to access U-Boot CLI.
            - Use the following commands to update the device to LEDE:
              run lfw
            - After that the device will reboot and boot to LEDE.
            - Wait until all LEDs stops flashing and use the router.
      
         2.Using httpd mode with Web UI connection and original LEDE image
            - Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
            - Connect PC with one of LAN ports,press the reset button, power up
              the router and keep button pressed for around 6-7 seconds, until
              leds flashing.
            - Open your browser and enter 192.168.1.1,You will see the upgrade
              interface, select "openwrt-ar71xx-generic-xxx-squashfs-
              sysupgrade.bin" and click the upgrade button.
            - After that the device will reboot and boot to LEDE.
            - Wait until all LEDs stops flashing and use the router.
      Signed-off-by: default avatar张鹏 <sd20@qxwlan.com>
      [cut out of bigger patch, keep swconfig, whitespace fixes]
      Signed-off-by: default avatarAdrian Schmutzler <freifunk@adrianschmutzler.de>
      4ff7bdfe
    • 张鹏's avatar
      ath79: add support for Qxwlan E558 v2 · 987d9028
      张鹏 authored
      Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327.
      
      Specification:
      
       - 720/600/200 MHz (CPU/DDR/AHB)
       - 128 MB of RAM (DDR2)
       - 8/16 MB of FLASH (SPI NOR)
       - 2T2R 2.4 GHz (QCA9558)
       - 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
       - 4x miniPCIe slot (USB 2.0 bus only)
       - 1x microSIM slot
       - 5x LED (4 driven by GPIO)
       - 1x button (reset)
       - 1x 3-pos switch
       - 1x DC jack for main power input (9-48 V)
       - UART (JP5) and LEDs (J8) headers on PCB
      
      Flash instruction:
      
         1.Using tftp mode with UART connection and original LEDE image
            - Configure PC with static IP 192.168.1.10 and tftp server.
            - Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
              to "firmware.bin" and place it in tftp server directory.
            - Connect PC with one of LAN ports, power up the router and press
              key "Enter" to access U-Boot CLI.
            - Use the following commands to update the device to LEDE:
              run lfw
            - After that the device will reboot and boot to LEDE.
            - Wait until all LEDs stops flashing and use the router.
      
         2.Using httpd mode with Web UI connection and original LEDE image
            - Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
            - Connect PC with one of LAN ports,press the reset button, power up
              the router and keep button pressed for around 6-7 seconds, until
              leds flashing.
            - Open your browser and enter 192.168.1.1,You will see the upgrade
              interface, select "openwrt-ar71xx-generic-xxx-squashfs-
              sysupgrade.bin" and click the upgrade button.
            - After that the device will reboot and boot to LEDE.
            - Wait until all LEDs stops flashing and use the router.
      Signed-off-by: default avatar张鹏 <sd20@qxwlan.com>
      [cut out of bigger patch, keep swconfig, whitespace adjustments]
      Signed-off-by: default avatarAdrian Schmutzler <freifunk@adrianschmutzler.de>
      987d9028
    • 张鹏's avatar
      ath79: add support for Qxwlan E750G v8 · 27a7d071
      张鹏 authored
      Qxwlan E750G v8 is based on Qualcomm QCA9344 + QCA9334.
      
      Specification:
      
       - 560/450/225 MHz (CPU/DDR/AHB)
       - 128 MB of RAM (DDR2)
       - 8/16 MB of FLASH (SPI NOR)
       - 2T2R 2.4G GHz (AR9344)
       - 2x 10/100/1000 Mbps Ethernet (one port with PoE support)
       - 7x LED (6 driven by GPIO)
       - 1x button (reset)
       - 1x DC jack for main power input (9-48 V)
       - UART (J23) and LEDs (J2) headers on PCB
      
      Flash instruction:
      
         1.Using tftp mode with UART connection and original LEDE image
            - Configure PC with static IP 192.168.1.10 and tftp server.
            - Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
              to "firmware.bin" and place it in tftp server directory.
            - Connect PC with one of LAN ports, power up the router and press
              key "Enter" to access U-Boot CLI.
            - Use the following commands to update the device to LEDE:
              run lfw
            - After that the device will reboot and boot to LEDE.
            - Wait until all LEDs stops flashing and use the router.
      
         2.Using httpd mode with Web UI connection and original LEDE image
            - Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
            - Connect PC with one of LAN ports,press the reset button, power up
              the router and keep button pressed for around 6-7 seconds, until
              leds flashing.
            - Open your browser and enter 192.168.1.1,You will see the upgrade
              interface, select "openwrt-ar71xx-generic-xxx-squashfs-
              sysupgrade.bin" and click the upgrade button.
            - After that the device will reboot and boot to LEDE.
            - Wait until all LEDs stops flashing and use the router.
      Signed-off-by: default avatar张鹏 <sd20@qxwlan.com>
      [cut out of bigger patch, keep swconfig]
      Signed-off-by: default avatarAdrian Schmutzler <freifunk@adrianschmutzler.de>
      27a7d071
    • Felix Fietkau's avatar
      base-files: remove block2mtd checks from sysupgrade · 4a0688ed
      Felix Fietkau authored
      This hasn't been used in a long time
      Signed-off-by: default avatarFelix Fietkau <nbd@nbd.name>
      4a0688ed
    • Felix Fietkau's avatar
      kernel: remove obsolete non-upstream block2mtd patches · 93f98b28
      Felix Fietkau authored
      Since block2mtd is not used for firmware images anymore, these patches
      are no longer needed
      Signed-off-by: default avatarFelix Fietkau <nbd@nbd.name>
      93f98b28
    • Felix Fietkau's avatar
      mac80211: fix memory leak on filtered powersave frames · 08a42ef0
      Felix Fietkau authored
      After the status rework, ieee80211_tx_status_ext is leaking un-acknowledged
      packets for stations in powersave mode.
      To fix this, move the code handling those packets from __ieee80211_tx_status
      into ieee80211_tx_status_ext
      Reported-by: default avatarTobias Waldvogel <tobias.waldvogel@gmail.com>
      Signed-off-by: default avatarFelix Fietkau <nbd@nbd.name>
      08a42ef0
  8. 16 Oct, 2020 6 commits